Accreditation · article

How to do a risk assessment for your trucking business

Ask a question

By RigsHQ · checked 7 Nov 2026 · published 7 Nov 2026

Short answer

A risk assessment means working out what could hurt someone in your transport work, how likely and how bad it would be, and what you will do about it. Write it in a risk register, put the controls in place, and check them regularly. It doesn’t need to be complicated – a simple register that you actually use is enough.

Why it matters

Under the Heavy Vehicle National Law, you must ensure, so far as reasonably practicable, the safety of your transport activities. A risk assessment is how you show you have thought about what could go wrong and done something about it. Risk management is also one of the five areas of the SMS Standard 2026, so an auditor will ask to see it.

Hazard, risk and control

WordWhat it meansExample
HazardSomething that could cause harmAn uneven load
RiskWhat could happen, who could be hurt, and how badlyThe load shifts and the truck rolls over
ControlWhat you do to stop it or make it less likely or less seriousA loading procedure, driver training, axle weight checks

The five steps

The five steps of risk assessment: find the hazards, assess the risk, put controls in place, monitor and review, keep improving
  1. 1. Find the hazards

    Walk through what your business actually does – loading, driving, fuelling, yard work, maintenance, dealing with customers’ sites. Ask your drivers. Look at incidents, near misses, faults and roadside inspections.

  2. 2. Assess the risk

    For each hazard, ask what could happen, who could be affected, how likely it is and how bad it would be. Take into account the controls you already have and whether they work. Deal with the highest risks first.

  3. 3. Put controls in place

    Get rid of the risk where you reasonably can. If you can’t, reduce it as far as reasonably practicable, using the most effective controls first.

  4. 4. Monitor and review

    Check the controls are being used and are working. Review the risk when something changes, after an incident or near miss, and at your scheduled reviews.

  5. 5. Keep improving

    Use what you learn from incidents, audits, inspections and driver feedback to fix controls and update your procedures.

Rating the risk

Example risk matrix rating likelihood against consequence, showing a load shift risk moving from high to medium after controls

Most businesses use a risk matrix: you rate how likely something is and how bad the consequence would be, and the matrix gives you a rating such as low, medium, high or extreme. The NHVR publishes a free risk assessment matrix you can use. Pick one, use it the same way every time, and decide what each rating means – for example, “extreme: stop until it’s fixed”.

Pick the strongest controls

Hierarchy of controls for trucking: eliminate, substitute, engineering and technology, procedures and training, PPE

Work down this list. The controls near the top work best because they don’t rely on people remembering to do the right thing.

ControlTrucking example
Eliminate the hazardHave the customer’s forklift load the truck so the driver isn’t climbing on the deck
Substitute something saferUse a tautliner instead of a flat-top for loads that need tarping
Engineering and technologySpeed limiters, reversing cameras, fall-arrest rails, telematics alerts
Procedures and trainingLoading procedure, journey planning, driver induction, toolbox talks
PPEGloves, hi-vis, safety boots

Most risks need a mix. A procedure on its own is the weakest option, so back it up with training, supervision and checks.

Common risks to start with

  • Fatigue and fitness for duty
  • Speed and scheduling pressure
  • Loading, load restraint and mass
  • Vehicle defects and maintenance
  • Falls from trucks and trailers
  • Reversing and yard traffic
  • Customer sites and third parties
  • Working alone and remote travel
  • Heat

Write it down in a risk register

Example risk register line for an uneven or poorly restrained load

For each risk, the NHVR says your register should show:

  • the hazard
  • the risk – what could happen, who could be harmed and how badly
  • the controls already in place
  • the risk rating
  • any extra controls you will add, and who will do it
  • when you will next review it

General information, not legal advice.

Sources

Related